Quickstart your first COMbricks project

 

Quickstart your introduction to the Procentec COMbricks range using a basic Eco Monitoring kit (or similar), such as that shown below, consisting of a Head Station and at least one Repeater module.

 

altThis allows checking and reporting on the status of one or more separate PROFIBUS networks. Your required network event data will be saved to local memory chip if and when the selected events occur. Alert reports may also be emailed over the Ethernet link to highlight significant changes, with up to four destination addresses available and/or shown by hardware alarm contacts to lamp, sounder or similar. Live and stored network status information can be seen at any time by browser access to the integrated COMbricks web server, using the Head Station IP address.

 

Connection is needed directly into PROFIBUS cables of the required network, with only minimal loading and no network address or programming needed. The new device will be invisible to the network Masters, much as if you were using ProfiTrace on a convenient piggy-back connector. If you need to mount the COMbricks kit away from the required network, you can easily do this using a Procentec Single Channel B1 PROFIBUS Repeater which will create a safe, full specification, PROFIBUS DP spur to the COMbricks kit. The B1 is also DIN rail mounted, needs 24 volt DC power and includes all required removable screw connectors, for both power and PROFIBUS cables. 

 

The above COMbricks kit needs about 7 cm of DIN rail space in your PROFIBUS cabinet, access to 24 volt DC power, scope for adding a short extension onto your PROFIBUS cables and maybe access for patch lead connection onto your site Ethernet LAN, if locally available. Power and PROFIBUS cable connections are made using supplied screw terminal connectors, or with network data connection onto the front panel 9-pin PROFIBUS connector.

 

The recommended basic COMbricks Eco Monitoring kit includes a Head Station and 1 Channel PROFIBUS Repeater (although illustration above shows a 2 Channel Repeater). The Head Station has an RJ45 connector for Ethernet link, two separate DC power connectors (for optional redundant supplies) and a micro-SD memory card to save set-up details, status logs and recorded messages. The Repeater takes DC power from the adjacent Head Station and, in the case of a single channel repeater, has two plug-in screw connectors on the lower edge for PROFIBUS segment connection, with associated terminator switch, and a front panel 9-pin D-type connector for this lower Channel 1. Additional front panel slide switches, visible on red backgrounds in above photo, determine how each incoming  segment is to be connected to the internal back-plane for automatic monitoring by the Head Station and possible onward connection to new output segments using addition modules or channels.

 

In our above illustration, we show a 2 Channnel Repeater, with additional PROFIBUS connectors on top edge, allowing for connection of a new outgoing segment from the monitored incoming segment on lower channel.

 

Once 24 volt power is applied to the COMbricks kit, link your PC computer Ethernet socket with a Cat 5e patch cable to the COMbricks Ethernet port. Cross-over patch lead is not usually needed. With the (free) Procentec COMbricks Discovery Tool program running (as below), click on the left hand search icon, which should soon add a single display line for any COMbricks kit located. Each such line shows the head station name (if set), Head Station firmware type (1A, 1B or 1C), device serial number and the MAC and IP addresses and device uptime.

 

altAfter selecting a required COMbricks report line, the Discovery Tool flash button may be used to trigger brief illumination of all Head Station LEDs on that particular device - so confirming successful contact with that unit.

 

Further icons on the Discovery Tool program toolbar may then be used to launch your web browser to view device status, if necessary first changing the device IP-address using an offered dialogue.

 

The COMbricks web server page starts at the Status Screen. Thereafter one can view other menu options and, once your Head Station is connected to at least one live PROFIBUS network, one may open the Live List and Statistics pages for display of live network status information in a very similar style to that shown by ProfiTrace. The following illustration shows typical display formats, including those from a Scope Repeater, which is needed for both the bar-graphs and waveforms shown here.

 

alt

 

 

 

 

 

 

 

For more comprehensive details of the various COMbricks web server pages click on the following link to view the Procentec Live COMbricks demo page

Live demonstration of COMbricks web server

and/or for commentry about his demo page, and more recent enhancements, try the following link

Live COMbricks demo Website Enhanced


For further information, see the latest version of the Procentec COMbricks User Manual